Updated Nov 18, 2026· 6 min read

Key takeaways

  • A ducted range hood with a 400-600 CFM blower suits most home cooks, a wall or roof-mounted inline exhaust fan suits kitchens with long duct runs, and a…

A ducted range hood with a 400-600 CFM blower suits most home cooks, a wall or roof-mounted inline exhaust fan suits kitchens with long duct runs, and a ductless recirculating hood only makes sense when venting outside is not possible. The right pick depends on how much the stove is used, how far the kitchen sits from an exterior wall, and how loud the household will tolerate the fan running.

What Actually Matters in a Kitchen Exhaust Fan

Three numbers decide whether a kitchen exhaust fan will keep a kitchen comfortable: airflow (measured in cubic feet per minute, or CFM), sound level (measured in sones), and duct size. Manufacturers generally size hoods so the blower can move roughly one CFM per 100 BTUs of cooktop burner output, though actual needed airflow also depends on kitchen volume and how often something is frying or searing. A fan rated for high CFM but forced through an undersized duct will perform far below its rating and run louder than expected, so duct diameter and run length matter as much as the blower spec on the box.

Sone ratings are worth checking separately from CFM. Many higher-airflow blowers climb past 6-8 sones at full speed, which is noticeably louder than a bathroom fan. Shoppers who cook daily and want to run the fan on medium without raising their voice to talk should look for lower sone ratings at the CFM level they actually need, rather than buying the highest-CFM unit available and running it on low.

Ducted Range Hoods

A ducted hood mounted above the range, wall-mounted or under a cabinet, remains the most common residential setup. These rely on an internal or external blower to push cooking exhaust, grease, and moisture outside through rigid or semi-rigid ductwork. Manufacturers across the category, including Broan, Zephyr, and Cosmo, list models in the 300-900 CFM range for standard residential kitchens, with capture area (the width of the hood relative to the cooktop) affecting real-world performance as much as blower power.

For buyers replacing an existing hood, matching the existing duct size (commonly 6 or 7 inch round, or a rectangular equivalent) avoids an expensive duct-rework project. For new installs or major remodels, a licensed contractor can size duct diameter to the chosen CFM so static pressure losses stay manageable.

Inline and Remote Blower Fans

Inline fans sit inside the ductwork itself, away from the hood, which lets the hood housing stay quieter since the noisiest component is now several feet away or in an attic or basement. This setup suits kitchens where the duct run is long or has several bends, since inline blowers are often available in higher static-pressure ratings that better tolerate duct resistance. The tradeoff is a more involved install, generally requiring attic, wall, or crawlspace access and is best handled by a contractor familiar with kitchen ventilation.

Ductless (Recirculating) Hoods

Ductless hoods filter air through charcoal or grease filters and return it to the room rather than venting outside. They are the practical choice for apartments, condos, or kitchens on an interior wall with no path to the outdoors. Reviewers at outlets covering kitchen ventilation consistently note that ductless hoods remove grease and some odor but do not clear heat or humidity the way a vented hood does, so buyers with a choice between a duct run and a ductless hood generally get better results from venting outside.

At a Glance

Type Best For Typical Stated Specs Limits
Ducted wall/under-cabinet hood Standard kitchens with an exterior wall nearby 300-900 CFM, 6-7 inch duct, variable-speed control Install needs ducting through wall or roof
Inline/remote blower Long or bent duct runs, noise-sensitive kitchens 400-1200+ CFM, higher static pressure rating More complex install, usually needs attic/basement access
Ductless/recirculating hood Interior kitchens, apartments, rentals Charcoal + grease filter stages, 150-400 CFM recirculated Vents nothing outside; filters need regular replacement
Downdraft or microwave-combo vent Islands, or kitchens wanting a dual-purpose appliance 300-400 CFM typical, compact footprint Lower capture efficiency than an overhead hood

Fit, Duct, and Compatibility Notes

  • Measure the existing duct opening before ordering a replacement hood; most under-cabinet and wall hoods ship configurable for 6 or 7 inch round duct, or a rectangular transition.
  • Hood width should generally match or exceed cooktop width for proper capture; a hood narrower than the range below it will miss smoke and steam from the front burners.
  • Check make-up air requirements in local building code; some jurisdictions require a make-up air damper once exhaust airflow passes a set CFM threshold, since a kitchen exhaust fan that strong can depressurize a tightly sealed home.
  • Confirm cabinet clearance above the range for under-cabinet hoods, and roof or wall penetration feasibility for any ducted install, before purchase.

Pick This If…

Situation Recommended Type
Standard kitchen, exterior wall within a short duct run Ducted wall or under-cabinet hood, mid CFM range
Long duct run, multiple elbows, or want a quieter hood housing Inline/remote blower fan
No path to the outside, apartment or rental Ductless recirculating hood
Frequent high-heat cooking, wok or heavy frying Higher CFM ducted hood with wide capture area, paired with adequate make-up air
Island cooktop, no overhead cabinet space Downdraft vent, understanding it captures less than an overhead hood

Alternatives Worth Considering

Microwave-hood combo units: These mount over the range and double as a microwave, with a built-in exhaust fan usually in the 300-400 CFM range. They save cabinet space but generally capture less than a dedicated hood because of a shallower, narrower intake.

Downdraft vents: Built into or behind the cooktop, these pull air downward and across the burners rather than up. They suit islands without overhead cabinetry but are less effective against rising heat and steam compared with an overhead hood.

Portable or window-mounted kitchen fans: Occasionally used as a stopgap in older homes, these are a weak substitute for a dedicated range exhaust fan and are generally not recommended as a primary solution for daily cooking.

Installation and Electrical Notes

Kitchen exhaust fans involve both electrical wiring and, for ducted models, cutting into a wall or roof. Any hardwired connection should be done by a licensed electrician, and duct penetrations through an exterior wall or roof should follow local code for flashing and clearance from combustible material. Always follow the manufacturer’s installation manual for minimum mounting height above the cooktop; mounting too low is a fire-safety and heat-exposure concern, and too high reduces capture efficiency.

Frequently Asked Questions

How much CFM does a typical kitchen exhaust fan need?

Many manufacturers suggest roughly one CFM per 100 BTUs of total burner output as a starting point, though actual kitchen volume, ceiling height, and cooking style also factor in. A kitchen with a high-BTU professional-style range generally needs more airflow than one with a standard home range.

Is a ducted or ductless hood better?

A ducted hood that vents outside removes heat, humidity, and odor more effectively, according to reviewers who have compared the two setups side by side. Ductless hoods are a reasonable fallback only when venting outside isn’t physically possible.

Why does my new exhaust fan seem weaker than its CFM rating?

Long or narrow ductwork, sharp elbows, and undersized duct diameter all reduce real-world airflow well below the rated CFM. The manufacturer’s installation manual usually lists the recommended duct size and maximum run length for a given blower.

Do I need a make-up air system?

Some local codes require a make-up air damper once exhaust CFM crosses a set threshold, since powerful exhaust fans can depressurize a tightly sealed home and affect other combustion appliances. A licensed contractor familiar with local code can confirm whether a specific installation needs one.

Can I install a range hood myself?

Mounting the hood body is often within reach for an experienced DIYer, but electrical hookup and any new duct penetration through a wall or roof are best left to a licensed electrician and contractor, both for safety and to meet local code.

How loud should I expect a kitchen exhaust fan to be?

Sone ratings vary widely by model and speed setting; many fans rated for higher CFM exceed 6-8 sones at full speed. Checking the sone rating at the specific speed setting likely to be used daily gives a better sense of real-world noise than the top-speed CFM number alone.

D
Dũng Trọc Hà Đông
We compare specs, materials and verified owner reviews before a product earns a spot. Rankings are never paid.
Affiliate disclosure. As an Amazon Associate we earn from qualifying purchases at no extra cost to you. Prices accurate as of the date shown.