Updated Nov 17, 2026· 8 min read

Key takeaways

  • For an A-frame camper, cargo or utility trailer, a sidewind A-frame jack rated well above your tongue weight, such as the TOWKING 5000 lb, Fulton Bulldog…

For an A-frame camper, cargo or utility trailer, a sidewind A-frame jack rated well above your tongue weight, such as the TOWKING 5000 lb, Fulton Bulldog or CURT A-frame, is the standard choice, a top-wind jack such as the MaxxHaul 70159 suits light trailers and tight budgets, and an electric jack such as the Lippert unit or a drill-driven jack suits people who hitch often or have trouble cranking. Match the jack to your coupler height, tongue shape and tongue weight first, then choose between manual and powered operation.

At a Glance: Trailer Jacks Reviewers Mention Most

Jack Best for Key stated specs Limits
TOWKING 5000 lb sidewind A-frame Farm, horse and camper trailers with A-frame tongues 5,000 lb rating, about 15 inches of travel, drop leg, bolt-on mounting Sidewind takes more crank turns than a top-wind
Fulton Bulldog 170010 Heavy-duty manual use 15-inch A-frame sidewind, weld-on or bolt-on Heavier, higher tier than basic jacks
CURT 28204 A-frame Lightweight A-frame use 2,000 lb lift, 15 inches of travel, sidewind Lower rating suits lighter trailers only
VEVOR 5000 lb A-frame Budget heavy rating with adjustable drop leg 5,000 lb rating, multi-position leg Fit and finish vary by batch per owners
YOMILINK 5000 lb Adjustable height 5-position drop leg Check bolt pattern against your tongue
MaxxHaul 70159 top-wind Entry-level, light trailers 2,000 lb rating, 14-inch lift Not for heavy tongue weight; tube mount only
Lippert electric A-frame jack Frequent hitching, push-button leveling 3,500 lb electric with manual crank backup Needs a power source; premium tier
Kohree 5000 lb drill-operated jack Speeding up manual cranking with a drill 5,000 lb rating, accepts a power drill Must be used with care; follow the maker’s drill guidance

These are the models that recur across independent roundups, many of which are affiliate-style. Specifications above come from the makers or reviewers’ summaries, and the right choice always starts with your trailer’s own numbers.

Start With Tongue Weight, Not the Biggest Number

Tongue weight is the downward force the coupler puts on the hitch. A common rule of thumb in towing guides is that it should be around 10 to 15 percent of the loaded trailer weight for conventional trailers, though your trailer maker’s manual is the authority. Pick a jack whose rated lift capacity comfortably exceeds the tongue weight, with extra margin because the load shifts when you load cargo, fill tanks or hitch up on a slope. A 2,000 lb jack is fine for a small utility trailer but is the wrong choice for a loaded camper. Many owners choose a 5,000 lb jack for mid-size campers for the margin, not because the tongue weighs that much.

A jack is a hitching aid. It is not designed to lift and support a trailer while you change a tire or work underneath. For that, use jack stands, wheel chocks and a procedure from the trailer maker’s manual.

Mounting Style: Match the Jack to Your Tongue

  • A-frame (bolt-on or weld-on): Mounts to the tongue of an A-frame trailer. Bolt-on versions avoid welding. Check the bolt pattern and clearances on your tongue before buying.
  • Tube or round mount (swivel): Clamps to a round tongue, common on small utility and boat trailers. A swivel lets you rotate it out of the way when driving.
  • Top-wind: The crank handle sits on top, like an upright tube. It is quick to operate from a standing position and simple to mount.
  • Sidewind: The crank is on the side, letting you work from beside the tongue. It is common on heavy-duty A-frame jacks. Reviewers note it takes more turns than a top-wind.
  • Drop-leg: A telescoping leg with a pin that adjusts the starting height, useful if your hitch height varies.

Travel, Height and Coupler Clearance

Measure the coupler height of your trailer when level and the height of your tow ball. The jack needs enough travel to lift the coupler over the ball. Most A-frame jacks list around 14 to 15 inches of travel, and drop-leg versions add adjustment. If your trailer sits high, such as a camper with a tall hitch, look at models with extra reach, which some roundups call out for high couplers. Also check retracted height, because a jack that is too long can drag on a steep driveway or dip when you cross a ramp.

Jack Foot: Pad, Wheel or Caster

The foot decides how the trailer moves when not hitched. A plain pad is stable but must be lifted to move the trailer. A wheel lets you roll the tongue around a yard or storage lot, which is handy for small trailers. On soft ground, pads sink; use a block or plate to spread load. Heavy campers usually do best with a stable pad and a second option for moving, as a wheel under heavy tongue weight can be hard to steer.

Manual, Drill-Assisted or Electric

  • Manual: Cheap, reliable and independent of power. Hand cranks need effort when the tongue is heavy.
  • Drill-assisted: Some jacks accept a power drill to speed up cranking. One outlet says this saves much of the time and effort. Follow the maker’s drill guidance and avoid over-driving the jack at the limits of travel.
  • Electric: Push-button operation from the trailer’s battery or a power supply. The Lippert A-frame jack mentioned by reviewers includes a manual crank as a backup. Electric jacks suit frequent hitching, heavy tongues and owners who cannot crank easily, but they depend on power and a good wiring setup.

Installation Basics

Before you drill or weld, measure the tongue width, the space between the frame rails and the position of the coupler. The jack should sit close to the coupler so the load is carried near the point where it acts, while leaving room for the hitch latch and safety chains. Use the hardware that comes with the jack or hardware of an equal grade, tighten bolts to the maker’s torque guidance, and recheck them after the first few trips. If the tongue is thin, bent or rusted, have it assessed before mounting any jack on it.

Materials, Weather and Maintenance

Look for a galvanized or powder-coated finish to resist rust, particularly if you store the trailer outdoors or tow near salt water. Grease moving parts as the maker advises, and clean the threads and gears. Inspect the jack before each season: look for bent legs, loose bolts, cracked welds and stiff cranks. Replace a jack that shows damage. If a jack feels very hard to turn, stop and look for a cause rather than forcing it.

Budget Tiers

Budget tier

The MaxxHaul top-wind and basic CURT or VEVOR jacks cover light trailers and occasional use. They keep cost down but may have simpler finishes and less margin on weight.

Mid-range tier

The TOWKING 5000 lb, Fulton Bulldog and YOMILINK jacks are the mainstream choice for campers, horse trailers and utility trailers, with higher ratings and drop legs.

Premium tier

Electric jacks such as the Lippert and drill-assisted units like the Kohree save effort and suit heavy or frequently used trailers. They cost more and add complexity.

Pick X If… Decision Table

If this describes you Pick Why
Mid-size camper or farm trailer with A-frame tongue TOWKING 5000 lb or Fulton Bulldog High rating, long travel, bolt-on or weld-on mounting
Light utility trailer CURT 28204 or MaxxHaul top-wind Lightweight, simple, lower cost
Tight budget with high rating VEVOR or YOMILINK 5000 lb Adjustable leg at lower tier
You hitch up often or have limited strength Lippert electric A-frame jack Push-button lift with manual backup
You want faster manual cranking Kohree drill-operated jack Accepts a drill to save effort
High coupler height Long-reach drop-leg jack Extra travel clears tall couplers
Round-tongue small trailer Swivel tube-mount jack Clamps to the tongue and rotates up

Alternatives to a Standard Tongue Jack

  • Tongue jack with caster wheel: Lets you move a small trailer by hand around a yard.
  • Trailer dolly: A separate wheeled unit that moves a trailer without hitching to a vehicle.
  • Bottle or scissor jack for tire changes: Not a replacement for the tongue jack, and should be used with stands as the manual instructs.
  • Leveling blocks and stabilizer jacks: These help keep a camper steady once parked but do not replace a tongue jack.

Safety Notes

  • Never get under a trailer supported only by a jack. Use jack stands and wheel chocks.
  • Chock the wheels before lifting or lowering the tongue, and stay clear of the coupler as it moves.
  • Do not exceed the jack’s rating. Keep a margin, and remember that loaded tongue weight can change.
  • Retract and secure the jack before driving so it does not hit the ground.
  • Follow the trailer maker’s manual for mounting, and use grade-appropriate bolts and a qualified welder where welding is needed.

Frequently Asked Questions

What size trailer jack do I need?

Choose a jack whose rated capacity is well above the loaded tongue weight of your trailer. Many owners of mid-size campers choose a 5,000 lb model for margin, while a 2,000 lb jack suits light utility trailers.

Is a sidewind or top-wind jack better?

Sidewind jacks suit A-frame tongues and let you work from the side, but reviewers note they need more turns. Top-wind jacks are quick and simple, and fit round tubes.

Can I use a trailer jack to change a tire?

No. A tongue jack is designed for hitching and leveling. Use proper jack stands and chocks and follow the trailer maker’s manual for wheel work.

Are electric trailer jacks worth it?

They are worth it for frequent hitching, heavy tongues or limited strength. They need a power source, and the better models include a manual crank as a backup.

Can I install a bolt-on jack myself?

Many owners do, if the bolt pattern matches the tongue and the correct hardware is used. For weld-on jacks or any doubts about the tongue structure, use a qualified welder or trailer shop.

How do I maintain a trailer jack?

Clean and grease the moving parts as the maker advises, check for rust, bent legs and loose bolts, and replace damaged jacks. Store the trailer with the jack on firm footing to protect the pad.

D
Dũng Trọc Hà Đông
We compare specs, materials and verified owner reviews before a product earns a spot. Rankings are never paid.
Affiliate disclosure. As an Amazon Associate we earn from qualifying purchases at no extra cost to you. Prices accurate as of the date shown.